P0207 OBD-II Trouble Code (Fuel Injector 7 Control Circuit Malfunction)

No doubt you know that an illuminated Check Engine Light (CEL) means that there's at least one sensor for a system in your engine or drivetrain that has registered a reading that's outside of normal specs. When that happens, the information is stored in the powertrain control module (PCM) as a trouble code, illuminating the CEL. From there, it's a simple matter for a technician (or you) to connect a code reader device to the multi-pin diagnostic port under the dash, usually on the driver's side. With the code reader, you can quickly access any trouble codes stored in the PCM and get a jump on diagnosing the problem.

The industry adopted OBD-II diagnostic protocols across the board in the mid-90s, with a standardized set of codes for all makes and models. It gives a huge head start in troubleshooting any problem, but it can get tricky when a single problem results in a string of trouble codes. In those events, the tech has to use some deduction and reading between the lines to narrow down the root cause and not just start replacing parts.

Note: Trouble code scanning is one of the services offered free of charge at your local Advance Auto Parts store.

Also, before proceeding with any troubleshooting, it's a good idea to find out if there are any recalls or Technical Service Bulletins (TSBs) that address your specific problem. You should also clear the trouble codes in the PCM and test-drive the vehicle to see if they return. Some problems on some year/make/models may require several failure cycles before a trouble code is stored again.

check engine light

 

P0207 — What It Means

A P0207 code means that the PCM has stored a trouble code indicating poor performance on a fuel injector on Cylinder 7. This could be due to a bad injector, an open or short connection, an intermittent open or short, a bad ground or even a bad PCM (though rare).

Note: on V6 and V8 engines, look for the cylinder bank that is offset slightly forward from the other and that bank will be the odd-numbered cylinders.

This trouble code is similar to P0201P0202P0203P0204P0205 and P0206, and P0208, and may be accompanied by one or more of those codes.

Symptoms

Symptoms can include:

  • Rough idle
  • Poor performance, lack of power
  • Poor fuel economy
  • Limp-in mode
  • Lean-running or rich-running condition
  • Misfire
  • Illuminated CEL

What Happens If I Ignore It?

Some vehicles will go into limp-in mode with this kind of trouble code, with the PCM limiting speed to 35 mph or less. Even if your vehicle doesn't go into limp-in mode, you'll notice poor performance and fuel economy that can lead to more serious engine damage. A rich-running condition can damage the catalytic converter, which will mean expensive repairs.

Diagnosis and Repair

  • Check the wiring to the injector for loose connection, damage or corrosion. Perform a wiggle test.
  • Using a multimeter, check the resistance of the injector. If this doesn't fall within spec, it may be the injector itself.
  • Once you've determined which cylinder is misfiring, you can easily check by using a test light (aka "noid light"). Disconnect the injector and plug the noid light into the connector. If the noid light flashes, as you crank the engine, the control circuit for that injector is working properly. If it doesn't flash, or stays on the entire time, there's a problem.
  • To test the circuit for power from the PCM, use a circuit test light and attach one lead to ground. Attach the other to the B+ pin on the connector. The light should illuminate. If the test light isn't lighting up or lights weakly or intermittently, use your multimeter for a voltage check as well.

Testing a circuit has the potential to get confusing. Remember that your best bet is to keep a cool head, use some critical thinking/deduction and keep it simple. Isolate the circuit into segments to rule out problems, starting with whatever is easiest and quickest for you to check. In this case, that means starting with a visual inspection and then moving on to the injector itself. If you need to replace a fuel injector, we've got you covered there, too.


Last updated December 29, 2020

Share

Comments